Whole house rewiring means stripping out outdated branch circuits and installing new copper NM-B cable, grounded receptacles, and arc-fault protection throughout a Wichita Falls property. Older homes in Downtown Wichita Falls and University Park often still run knob-and-tube or 60-amp panels that cannot safely carry modern loads. We pull permits through the city, replace the main panel when needed, and bond the system to the water pipe and ground rods. Every circuit is traced before demolition so we know which switches control which rooms. As a locally owned, owner-operated electrician Wichita Falls residents can reach Mon–Fri 8am–6pm and Sat 9am–2pm, we provide upfront quotes and leave workmanship you can inspect.
Wichita County weather shapes how we run cable. Hot summers and cold winters with high winds cause attic temperatures to swing, so we route NM-B away from direct roof heat and staple it securely to resist wind-driven vibration in older frames. Homes near Lake Wichita often sit on shifting soil that can crack foundations and stress conduit entries, while Southside bungalows frequently have plaster walls that require careful fish-tape work to avoid large patches. We check for water intrusion at service masts before energizing anything, because wind-driven rain around Memorial Auditorium and the Kell House Museum has corroded more than one main lug. Each job is scoped for access, not just square footage.
Aluminum branch wiring from the 1960s and 1970s still turns up in University Park additions, and it cannot be pigtailed to standard receptacles without approved connectors. We flag ungrounded two-prong outlets, missing GFCI protection in kitchens and baths, and double-tapped breakers before any rewire begins. Lockout/tagout at the panel, voltage testing at every box, and a final continuity check keep the crew and the house safe. Homeowners in lawton, burkburnett, and henrietta sometimes ask about similar work, but we focus our crews on Wichita Falls proper so we can respond during business hours and return for callbacks without delay.
Technician insight
In Wichita Falls, the thing that catches most people out with whole house rewiring is attic heat. Once summer temperatures climb, cable insulation in a poorly vented attic can degrade faster than expected, so we route new runs where airflow stays higher. I also see a lot of Southside homes with plaster walls that turn a simple fish tape job into a patch-and-paint project if you are not careful.
Southside Bungalow With Two-Prong Outlets
A homeowner called because every outlet in the living room was ungrounded and the breaker kept tripping when the window AC ran. We opened the walls and found 1950s cloth-sheathed cable with no ground path running through the attic. We replaced the branch circuits with grounded copper, added AFCI protection, and updated the panel labeling. The homeowner now runs the air conditioner and space heater on the same circuit without tripping.
Whole House Rewiring Services We Offer
✓Knob-and-Tube Replacement
Removing obsolete knob-and-tube circuits common in older Downtown Wichita Falls homes and replacing them with grounded copper cable reduces fire risk and supports modern appliances.
✓Aluminum Wiring Remediation
Replacing or properly terminating 1960s aluminum branch wiring found in some University Park additions prevents overheating at outlets and switches.
✓Main Panel Upgrade and Replacement
Swapping an undersized 60-amp or 100-amp panel for a 200-amp service gives Wichita Falls households enough capacity for HVAC, EV chargers, and whole-home surge protection.
✓Attic and Crawlspace Cable Replacement
Running new NM-B through attics and crawlspaces while shielding it from high-wind vibration and temperature swings keeps insulation intact and connections secure.
✓GFCI and AFCI Circuit Installation
Adding ground-fault and arc-fault protection to kitchens, baths, and bedrooms meets current safety expectations and protects older Wichita County wiring from nuisance trips.
✓Historic Home Whole House Rewiring
Rewiring older properties near the Kell House Museum or Memorial Auditorium preserves plaster walls and original trim while bringing circuits up to modern standards.
How it works
- 1
Initial Inspection and Load Calculation
We map every existing circuit, check panel capacity, and identify aluminum or knob-and-tube wiring across the home before quoting.
- 2
Permit and Material Staging
We pull city permits, order copper NM-B, breakers, and devices, and schedule work during our Mon–Fri 8am–6pm or Sat 9am–2pm windows.
- 3
Circuit Rewire and Rough-In
Old cable is removed, new grounded runs are installed through attics, crawlspaces, and walls, and boxes are secured to resist local wind-driven vibration.
- 4
Trim-Out and Device Installation
Receptacles, switches, GFCI and AFCI protection are installed, and the panel is wired with labeled circuits for easy future service.
- 5
Final Testing and Inspection
We test continuity, polarity, and grounding, coordinate the city inspection, and walk the homeowner through the completed work.
Pricing
Pricing depends on home size, panel age, accessibility of attics and crawlspaces, whether the main panel needs replacement, and how many circuits require new runs. We provide upfront quotes after an in-person inspection.